If you are a proud owner of a Briggs and Stratton pressure washer, you know that it is a powerful tool that can make your cleaning tasks a breeze. Whether you need to clean your car, your patio, or any other surface, a pressure washer can help you get the job done quickly and efficiently. However, if you are new to pressure washers, you may be wondering how to start it. In this article, we will guide you through the process of starting a Briggs and Stratton pressure washer, so you can get started on your cleaning tasks in no time!

The first thing you need to do when starting a Briggs and Stratton pressure washer is to ensure that you have all the necessary equipment. This includes safety goggles, gloves, and hearing protection. It’s also important to have a clean and dry area to work in, away from any flammable materials. Once you have all the necessary equipment, you can move on to the next step.

Next, you will need to check the oil level in the engine. To do this, locate the oil dipstick and remove it. Wipe it clean with a rag, and then reinsert it into the oil fill tube without screwing it in. Remove the dipstick again and check the oil level. If the oil level is below the “Full” mark on the dipstick, you will need to add oil. Refer to your pressure washer’s manual for the correct type and amount of oil to use.

Once you have checked the oil level and added oil if necessary, you can move on to the next step, which is to connect the water supply. Start by attaching the garden hose to the water inlet on the pressure washer. Make sure it is securely attached to prevent any leaks. Turn on the water supply and let it flow through the hose, clearing out any air pockets. Once the water is flowing smoothly, you can move on to the final step – starting the engine.

To start the engine, locate the engine switch or ignition switch on your pressure washer. It is usually labeled with a symbol resembling a lightning bolt. Move the switch to the “ON” position. If your pressure washer has a choke, move it to the “CHOKE” position. You may also need to pull the recoil starter handle to start the engine. Once the engine is running, you can release the recoil starter handle. Congratulations! You have successfully started your Briggs and Stratton pressure washer and are ready to tackle your cleaning tasks.

VEVOR Pressure Washer Pump, 7/8" Shaft Vertical, 3400 PSI, 2.5 GPM, Replacement Power Washer Pumps Kit, Parts Washer Pump, Compatible with Honda, Simpson, RYOBI, Briggs & Stratton, Subaru, Craftsman
VEVOR Pressure Washer Pump, 7/8" Shaft Vertical, 3400 PSI, 2.5 GPM, Replacement Power Washer Pumps Kit, Parts Washer Pump, Compatible with Honda, Simpson,...
$56.99
$50.99
Amazon.com
Amazon price updated: October 16, 2024 11:53 pm

Tips for starting a Briggs and Stratton pressure washer

Starting a Briggs and Stratton pressure washer is a simple task, but it is important to follow the correct steps to ensure safe and efficient operation. Here are some tips to help you start your Briggs and Stratton pressure washer:

  1. Before starting the pressure washer, check the oil level and fill it if necessary. Make sure to use the recommended oil type specified in the owner’s manual.
  2. Inspect the fuel tank and ensure that it is filled with fresh gasoline. If the fuel has been sitting for a long time, it is recommended to drain and replace it with fresh fuel.
  3. Check the spark plug and clean or replace it if necessary. A fouled or damaged spark plug can cause starting issues.
  4. Turn on the fuel valve, if applicable, and ensure that the choke is in the correct position for starting. Refer to the owner’s manual for guidance.
  5. Locate the engine on/off switch and turn it to the “on” position. This switch is usually located on the control panel.
  6. Move the throttle lever to the “fast” or “run” position. This will allow the engine to run at full power.
  7. Slowly pull the starter rope to start the engine. It may take a few pulls to get the engine running.
  8. Once the engine starts, allow it to warm up for a few minutes before applying pressure.
  9. Engage the spray gun trigger to release the water pressure and begin using the pressure washer.
  10. After using the pressure washer, turn off the engine and release any remaining pressure by squeezing the trigger on the spray gun.
  11. Properly store the pressure washer in a clean and dry location, following the manufacturer’s instructions.

Following these tips will help ensure a smooth and successful start for your Briggs and Stratton pressure washer, allowing you to tackle your cleaning tasks with ease.

See also  How To Pressure Wash A Car Motor

Preparing for the first use

Before starting your Briggs and Straton pressure washer for the first time, there are a few steps you need to take to ensure everything is ready to go.

1. Read the manual

The first step is to carefully read the instruction manual provided by Briggs and Straton. This will give you a comprehensive understanding of the pressure washer’s features, safety precautions, and maintenance requirements. It’s important to follow the manufacturer’s recommendations to prevent any damage to the equipment.

2. Assembly

Next, assemble the pressure washer according to the instructions in the manual. This may involve attaching the handle, wheels, and other components. Make sure all the connections are secure and double-check for any loose parts.

YAMATIC 7/8" Shaft Vertical Pressure Washer Pump, 2600-3000 PSI @2.5 GPM OEM & Replacement Pump for Power Washer, Replacement with Troybilt, Briggs&Stratton, Craftsman, AR, Honda Front Inlet/Outlet
YAMATIC 7/8" Shaft Vertical Pressure Washer Pump, 2600-3000 PSI @2.5 GPM OEM & Replacement Pump for Power Washer, Replacement with Troybilt, Briggs&Stratton,...
$125.99
$89.99
Amazon.com
Amazon price updated: October 16, 2024 11:53 pm

3. Fuel and oil

Check the fuel and oil levels before starting the pressure washer. Fill the fuel tank with fresh gasoline and ensure that the oil reservoir is filled with the recommended oil type. Refer to the manual for specific instructions on how much fuel and oil to add.

4. Water supply

Connect a garden hose to a water source and attach it to the pressure washer. Ensure that the water supply is turned on and that there are no kinks or obstructions in the hose that could restrict the flow of water.

5. Safety precautions

Prior to starting the pressure washer, be sure to take necessary safety precautions. This includes wearing safety goggles, hearing protection, and work gloves. Make sure you are in a well-ventilated area and keep children and pets away from the operating area.

Precautions Reason
Wearing safety goggles To protect your eyes from debris or high-pressure water.
Wearing hearing protection To prevent hearing damage from the loud noise of the pressure washer.
Wearing work gloves To protect your hands from potential injuries or chemical contact.
Working in a well-ventilated area To prevent inhalation of fumes or exhaust emissions.

By following these steps and taking the necessary precautions, you will be well-prepared for the first use of your Briggs and Straton pressure washer. Once everything is set up and checked, you can proceed to start the pressure washer according to the instructions in the manual.

Checking the fuel and oil levels

Before starting your Briggs and Stratton pressure washer, it is important to check the fuel and oil levels to ensure that your equipment is properly lubricated and fueled.

YAMATIC 7/8" Shaft Vertical Pressure Washer Pump, 2200-2500 PSI @2.2 GPM Replacement Pump for Power Washer, Replacement with Troybilt, Briggs&Stratton, Craftsman, AR, Honda Front Inlet/Outlet Silver
YAMATIC 7/8" Shaft Vertical Pressure Washer Pump, 2200-2500 PSI @2.2 GPM Replacement Pump for Power Washer, Replacement with Troybilt, Briggs&Stratton,...
$79.99
Amazon.com
Amazon price updated: October 16, 2024 11:53 pm

First, locate the fuel tank on the pressure washer. The tank is typically located near the engine and may have a removable cap or a fuel gauge. Remove the cap and visually inspect the fuel level. If the tank is less than half full, it is recommended to fill it with fresh gasoline. Make sure to use the correct fuel type as specified in the manufacturer’s instructions.

Next, check the oil level in the engine. Locate the oil dipstick, which is usually located near the engine block. Remove the dipstick and wipe it clean with a rag or paper towel. Insert the dipstick back into the oil well fully and then remove it again to check the oil level. The dipstick should have two marks indicating the minimum and maximum oil levels. The oil level should be between these two marks. If the oil level is below the minimum mark, you will need to add oil. Refer to the manufacturer’s instructions for the recommended type and amount of oil to add.

Regularly checking the fuel and oil levels of your Briggs and Stratton pressure washer will help ensure that it operates smoothly and efficiently. It is important to maintain the proper fuel and oil levels to prevent damage to the engine and ensure the longevity of your equipment.

Connecting and priming the water supply

Before starting your Briggs and Stratton pressure washer, it is important to properly connect and prime the water supply. Follow these steps to ensure smooth operation:

1. Connect the water hose

Start by connecting one end of a garden hose to the water inlet on the pressure washer pump. Make sure to securely tighten the connection to prevent any leaks.

AgiiMan High Pressure Washer Pump Head - Replacement Water Gasoline Pump, 2800 Psi Troy Bilt SRMW22G26-EZ Oil Pump Accssories Fits KARCHER Craftsman, Front Facing Inlet Outlet
AgiiMan High Pressure Washer Pump Head - Replacement Water Gasoline Pump, 2800 Psi Troy Bilt SRMW22G26-EZ Oil Pump Accssories Fits KARCHER Craftsman, Front...
$99.99
Amazon.com
Amazon price updated: October 16, 2024 11:53 pm

2. Connect the other end of the hose

Connect the other end of the garden hose to a nearby outdoor water source, such as a spigot or faucet. Again, ensure a tight connection to prevent any water leakage.

See also  What Does A Capacitor Do In A Pressure Washer

3. Turn on the water

Before starting the pressure washer, turn on the water supply by opening the outdoor water source completely. This will allow water to flow freely into the pressure washer.

4. Prime the pump

Once the water is flowing, it is important to prime the pump to remove any air and ensure proper functioning. Follow these steps to prime the pump:

  1. Turn the pressure washer on/off switch to the “Off” position
  2. Turn the water inlet valve to the “On” position
  3. Squeeze the trigger on the pressure washer wand to allow water to flow through the system
  4. Continue squeezing the trigger until a steady stream of water is coming out of the wand

By priming the pump, you are ensuring that the pressure washer is ready to deliver consistent water pressure during operation.

Once you have successfully connected and primed the water supply, you are now ready to start your Briggs and Stratton pressure washer and tackle your cleaning tasks with ease.

MUTURQ 3/4" Shaft Horizontal Pressure Washer Pump, Easy Adjust 2000-3000 PSI, 2.5 GPM, OEM Replacement Pump for Simpson, Honda GC 160, Homelite, and Most Power Washer
MUTURQ 3/4" Shaft Horizontal Pressure Washer Pump, Easy Adjust 2000-3000 PSI, 2.5 GPM, OEM Replacement Pump for Simpson, Honda GC 160, Homelite, and Most...
$82.99
$77.99
Amazon.com
Amazon price updated: October 16, 2024 11:53 pm

Starting the engine

To start a Briggs and Stratton pressure washer, follow these steps:

1. Prepare the equipment

Before starting the engine, make sure you have completed the necessary preparations:

  • Check the oil level: Ensure that the oil level is correct. If it is low, add the recommended oil for your engine model.
  • Check the fuel level: Make sure there is enough fuel in the tank to run the pressure washer.
  • Inspect the air filter: Remove the air filter cover and inspect the air filter. If it is dirty, clean or replace it.
  • Inspect the spark plug: Check the condition of the spark plug. If it is dirty or worn out, replace it.
  • Connect the water supply: Attach a garden hose to the water inlet of the pressure washer.
  • Ensure proper ventilation: Make sure the engine is in a well-ventilated area to prevent carbon monoxide build-up.

2. Set the choke and throttle

Set the choke and throttle in the correct positions:

  • Choke: Move the choke lever to the “Choke” position if the engine is cold. If the engine is already warm, skip this step.
  • Throttle: Set the throttle to the “Run” or desired speed setting for the pressure washer.

3. Pull the starter cord

With one hand on the engine handle and the other hand on the starter cord handle, follow these steps to start the engine:

  1. Pull the starter cord slowly until you feel resistance, then give it a quick, smooth pull to start the engine.
  2. Allow the engine to warm up for a few moments before using the pressure washer.

Note: If the engine does not start after a few attempts, check the fuel and oil levels again, and make sure the spark plug is clean and properly connected.

Mikatesi 7/8" Shaft Vertical Pressure Washer Pump for SRMW22G26-EZ 2.2G24, 2.2 2.5 GPM 2600-3000 PSI for TroyBilt Karcher Craftsman Generac Fits Most 4-7 HP Engines with 5 Nozzle
Mikatesi 7/8" Shaft Vertical Pressure Washer Pump for SRMW22G26-EZ 2.2G24, 2.2 2.5 GPM 2600-3000 PSI for TroyBilt Karcher Craftsman Generac Fits Most 4-7 HP...
$88.99
Amazon.com
Amazon price updated: October 16, 2024 11:53 pm

Once the engine is running, you can begin using the Briggs and Stratton pressure washer for your cleaning tasks.

Operating the pressure washer

Once you have properly started your Briggs and Stratton pressure washer, you are ready to begin operating it. Here are the steps to follow:

  1. Make sure you have connected a water source to the pressure washer and that it is turned on.
  2. Attach the suitable spray nozzle to the spray wand. The type of nozzle you should use will depend on the task at hand.
  3. Before starting the engine, be sure to release the pressure in the pump by squeezing the trigger on the spray wand. This will prevent any damage to the pump.
  4. Next, start the engine of the pressure washer according to the instructions provided in the user manual.
  5. Once the engine is running, slowly squeeze the trigger on the spray wand to start spraying water. Begin with a low-pressure setting and gradually increase the pressure as needed.
  6. Move the spray wand back and forth in a sweeping motion to evenly clean the desired surface.
  7. If you need to change the pressure setting or switch to a different spray nozzle, release the trigger and make the necessary adjustments.
  8. When you have finished using the pressure washer, release the trigger and turn off the engine.

Remember to always follow the manufacturer’s instructions and safety guidelines when operating your Briggs and Stratton pressure washer. Regularly inspect and maintain your pressure washer to ensure its optimal performance and longevity.

Shutting down and storing the pressure washer

Properly shutting down and storing your Briggs and Straton pressure washer is essential for its long-term durability and performance. Follow these steps to ensure you store your pressure washer correctly:

See also  What Are The Benefits Of Pressure Washing

Step 1: Turn off the engine

Begin by turning off the pressure washer engine. This can be done by turning the key or switch to the “Off” position.

YAMATIC 3/4" Shaft Horizontal Pressure Washer Pump 3400 PSI @ 2.5 GPM Replacement Pump for Power Washer Compatible with Homelite, Troybilt, Simpson, Karcher Honda GC160 GC190 and More.
YAMATIC 3/4" Shaft Horizontal Pressure Washer Pump 3400 PSI @ 2.5 GPM Replacement Pump for Power Washer Compatible with Homelite, Troybilt, Simpson, Karcher...
$69.99
Amazon.com
Amazon price updated: October 16, 2024 11:53 pm

Step 2: Release pressure

Next, release any pressure that may be in the system by squeezing the trigger on the spray gun. This will prevent any damage to the internal components of the pressure washer.

Step 3: Disconnect hoses

Disconnect any hoses or accessories attached to the pressure washer. This will make it easier to store and prevent any damage or tangling of the hoses.

Step 4: Drain water

Before storing your pressure washer, make sure to drain any remaining water from the system. This can be done by removing the water inlet hose and holding the trigger on the spray gun until all water has been drained.

Step 5: Clean and dry

Thoroughly clean the pressure washer, including the spray gun, hoses, and nozzles, to remove any dirt or debris. After cleaning, allow all components to dry completely to prevent any rust or corrosion.

Step 6: Store in a cool and dry place

Find a cool and dry place to store your pressure washer. It is recommended to store it in a shed or garage to protect it from the elements and extreme temperatures.

Remember:

Always refer to the owner’s manual for specific instructions on shutting down and storing your Briggs and Straton pressure washer. Following the manufacturer’s guidelines will ensure the best performance and longevity of your equipment.

By properly shutting down and storing your pressure washer, you can extend its lifespan and ensure it is ready for use when you need it again.

Questions and answers,

What is a Briggs and Stratton pressure washer?

A Briggs and Stratton pressure washer is a cleaning device that uses a high-pressure stream of water to remove dirt and grime from various surfaces. It is powered by a Briggs and Stratton engine, which provides the necessary power to create the high-pressure water stream.

What are the main components of a Briggs and Stratton pressure washer?

The main components of a Briggs and Stratton pressure washer are the engine, the pump, the high-pressure hose, the spray wand, and the nozzle. The engine provides power to the pump, which creates the high-pressure water stream. The hose, wand, and nozzle help to direct and control the flow of water.

How do I start a Briggs and Stratton pressure washer?

To start a Briggs and Stratton pressure washer, first, make sure that there is fuel in the tank and that the engine oil level is correct. Next, connect the high-pressure hose and the spray wand to the pump. Turn the fuel valve to the “on” position and pull the starter cord to start the engine. Once the engine is running, squeeze the trigger on the spray wand to release the water.

What should I do if my Briggs and Stratton pressure washer doesn’t start?

If your Briggs and Stratton pressure washer doesn’t start, there are a few things you can check. First, make sure that there is fuel in the tank and that the engine oil level is correct. Check that the spark plug is clean and in good condition. If these things are all in order, try cleaning or replacing the air filter. If the problem still persists, it may be necessary to take the pressure washer to a qualified technician for further diagnosis and repair.

Can I use any type of detergent with a Briggs and Stratton pressure washer?

No, not all detergents are suitable for use with a Briggs and Stratton pressure washer. It is important to use a detergent that is specifically designed for use with pressure washers. These detergents are formulated to work with the high-pressure water stream and can help to enhance the cleaning power of the pressure washer. Using the wrong detergent can potentially damage the pump or other components of the pressure washer.

What is a Briggs and Stratton pressure washer?

A Briggs and Stratton pressure washer is a portable machine that uses high pressure water spray to clean surfaces. It is powered by a Briggs and Stratton engine, which provides the necessary power to operate the pump that generates the high pressure water.